This article outlines the history of the deckle edge, and explains a few techniques for creating your own edge on your prints or original paintings.

For more information on float framing your art, see our article on Mounting Art in a Frame.

SUMMARY

THE DECKLE EDGE	CREATING BY HAND	TOOLS FOR QUICK EDGES	ORDERING YOUR PRINTS
Unavoidable prior to the 19th century, deckle edges later became a symbol of an "authentic" book/paper.	By scoring the paper along a straightedge, creasing, and gently tearing it, a deckle edge can be easily achieved.	Deckle edge scissors and rulers make it easy to create a deckle edge.	We suggest ordering one size up in order to have a 2" border around your prints. This will make it easier to create a deckle edge.

Once the method of making separate pages had been fine-tuned enough to leave the edges smooth and straight, the deckle edge became something of a status symbol, a representation of the "Real Book."

Though not technically the same as a deckle edge, uncut pages in old books did create a similar look. Books were once assembled by folding a length of paper and binding along the open edge. Due to pages lined up unevenly, or a poor blade, these books often had a few pages still connected to one another along the short edge, perpendicular to the spine. To open these pages, the reader was required to use a penknife and draw it along the fold, which often left a rough edge.

In general, the thicker the paper the more extreme your deckle edge will be. A sheet of basic bond, 20 lb paper with create a fuzzed edge, but lack those attractive paper fibers that create a realistic deckle.

In the realm of thick papers, cold press - textured - paper works best. This seems to be due to the delicacy of the fibers, which is required to give the paper that bumpy, soft feel. Cold press papers are also a more "traditional" paper style, the kind that would have had deckle edges in centuries past. Hot press - smooth - papers work as well, though the crease is more difficult to tear, and can give a rougher, more deliberate edge.

DECKLE EDGE BY HAND

1. Determine where you want your edge to be. Since you will be folding and tearing the paper, your edge must be set in from the existing edge of the paper - an inch or more will make this process easier, though it is possible with less.

   If you are using a print, you may want to have it printed with crop marks. Cut through the crop lines with a utility knife, so you can see where they are on the back side of the paper. If you don't have crop marks, you can cut or poke holes through the paper at the corners. Be sure to measure so the border is even on each side of the image.

2. Turn the artwork over so it is lying face down. Put a protective sheet beneath the image, or make sure the surface is very clean. You should be able to see the corners you marked with the utility knife from the back side of the paper.

3. Place a straightedge or ruler across the paper, connecting the marks on either side. Run the back side of the utility knife along the straightedge. You don't want to cut right through, just break up the fibers on that side of the paper.

4. Fold the paper along the line you just made so it folds onto the image side. Crease it well, but be careful not to create a second score mark with your nail or tool.

5. Fold the paper along the line again, so it folds onto the back side of the paper. Now stop. Don't keep folding back and forth, because the easier you make it to rip, the less rough your edge will be.

6. Flatten out the paper again. Placing your non-dominant hand on the face of the print (you may want gloves), use your dominant hand to carefully begin pulling the paper apart at the crease. Make sure to pull out and away, not up, and don't try to tear it along a table edge. Go slowly so the paper fibers are gently pulled apart - this will leave you more of those nice little strands.

7. And that's it! Repeat the steps on each side of the print to create your very own vintage deckle edge. After all that hard work, you'll want to check out our article on Mounting Art in a Frame. We explain how to float mount your art so the edge is visible and becomes a part of the piece.

There's another relatively simple way to create a deckle edge. if you know that your paper has been sized - meaning it is now water-resistant. If this is the case, you can simply draw a line of water along a straightedge using a fine brush, let it soak in a bit, and then tear along the line. This doesn't work on all papers, so be sure to try it on a scrap piece before your print or original.

The score mark breaks the fibers but does not cut through

Fold along the scored line, once on each side

Deckle edges after tearing

Deckle Edge Scissors

Deckle/Straight Edge

Logan appears to no longer offer this tool, though they may still be available through other retailers, and no doubt other brands offer a similar product.

Dual Edge Ripper:

Dual Edge Ripper

Various brands including Hahnemuhle, which we use here at KeenART Media, offer this type of paper. The existing rough edge saves you the time and effort of having to create it yourself, and it is formulated to pass through the printer without jamming (which might happen if you tried to print on paper you had torn yourself).

The downside to pre-cut deckle edge paper is the size limit. Since you want to preserve the edge, you must use the paper in the size it came in - no trimming or cropping. As such, you are limited to the sizes provided by the company.

Hahnemuhle offers their smooth Photo Rag, and textured Museum Etching and William Turner papers with a pre-cut deckle edges in 3 different sizes:

• 8.5x11"
• 13x19"
• 17x22"

PAPER TYPE

Our Hahnemuhle Fine Art and Baryta papers work as well, though the deckle edge will be more subtle. Photographic papers may also work, with a similar result.

We are happy to supply test strips of any of our fine art papers for you to experiment. Please contact us to discuss samples.

PAPER SIZE

For example, if your print is 8"x10", order a 10"x12" print, but tell us you want a 2" border and still only an 8x10" image.

As mentioned above, it is possible to create a deckle edge with less than an extra inch around the border, but the less paper there is to remove, the more difficult the process becomes.

Deckle edge print in a floater frame

If you have any questions about any of the products or services offered here at KeenART Media, please do not hesitate to contact us. Our knowledgeable staff are always happy to answer your enquiries and provide suggestions or advice.

Want to see some great examples of deckle edged art? Check out our Pinterest Page!

A division of USAOnCanvas.com Houston prints on canvas - Gallery Picture Frames SanAntonio Laser Engraving & Cutting Services